nickjean

Hi again, If I install and configure the SCCM 2012 beta 2 now, can I make an update from that to the SCCM 2012 final version, when the final version is released? Thanks

Hi, Yes I know but I didn't mean the beta version. I mean the final version 2012. Regards

ok

Hi There, Does anyone knows when will System Center Configuration Machine Manager 2012 be released? Regards Nick

Hi, Thank you for replay. We have at the time a range of 192.168.1.1 until 192.168.1.254 subnet mask 255.255.255.0.We have not enough IP now and I want to to increase my hosts to 1024. I think you are right that it is better that I create one scope and without relay agent. If you have any better idea, feel free and write me again Regards Nick

Hi again, Thanks for replay. I am not sure that I dont need a DHCP relay agent. I can remember that MS has recommed me to do it. Here is the message from Microsoft: ################### Yes, we need to create 4 DHCP scopes, one for each subnet. To do so, we also need to configure DHCP relay agents for each subnet. Generally speaking, there are two ways to configure DHCP relay agents .First, to configure routers act as a configure DHCP relay agents. In most cases, routers support DHCP relay. If your routers do not, contact your router manufacturer or supplier to find out if a software or firmware upgrade is available to support this feature.Second, we can configure a computer running Windows Server® 2008 to act as a relay agent by installing the DHCP Relay Agent service. ######################################## What do you mean about this resulotion? Regards

Hi Anyweb, I have the same issue. I have installed the agent with domain adminstrator account.I have a domain and my scom is joined this domain and my other Computer joined the domain too. I did try to install the agent on all my computer with domain administrator account and I did not get any error during installing agent the install was successfull. What do you mean with local admin rights? Which MPs should I install for that? Kind Regards Nick

Hi Sabe75, Thank you very much for your replay.Now I can understand you what you mean.Are you sure if I create a scope of 192.168.0.0/22 that particular IP-Range is included? I mean if I create a scope with for example: 192.168.0.30 until 192.168.3.200 /22, would I have 1022 hosts? Have I to create a DHCP Relay Agent too or not? I think yes Kind Regards Nick

Hi, Thank you for your answer. But I dont understand you. I should create a single scope with 192.168.0.0 until 192.168.0.254 subnet mask 255.255.252.0 And what is happening withe othe range 192.168.1.1 and 192.168.2.1 and 192.168.3.1? I need 1024 hosts. Your descrition I only will have 254 hosts Regards Nick

I want to put a new DHCP Server with IP 192.168.0.0 and subnet mask 255.255.252.0 that would give me following IP-Range 192.168.0.1 - 192.168.0.255 192.168.1.1 - 192.168.1.255 192.168.2.1 - 192.168.2.255 192.168.3.1 - 192.168.3.255 My question is: Have I to define 4 Scopes? If yes which Subnet mask should I use for each scope? I did try to put 4 scopes but it does not work. My first scope is called 192.168.0.26 until 192.168.0.200 with subnet mask 255.255.252.0 But if want to define the secound scope with 192.168.1.26 until 192.168.1.200 with subnet mask 255.255.252.0, I get a error message: " the address range and mask conflict with an existing scope". Does it correct step? Or do I make a mistake Thanks for help Nick

Hi Paul, Thank you for your replay. Which GPO do you mean? Do you mean GPO of my Domain/Domain Comtroller? Or GPO of my SCOM Computer? I think you mean the GPO of all my Computer which is installing SCOM Agent. Am I right? Thanks Nick

Hi There, I have the same issue. Could you tell me please how and where do you adding the action account to the GPO? Regards Nick

ok thanks for reply. I will try it and let you know regards

Ok I uderstand it, I still will do it again all steps. But my problem is how to find or create a "install.wim"? I want to deploy XP and not Vista. This "install.wim" is on your guide for Vista or?

thank you for reply. Yes I do follow step by step your guide for deploy XP and I imported the computer ind sccm with MAC-Address. But it happend nothing and PXE does not startet and I cannot see any PXE boot Client. by this point: Create distribution point and then update it complete the following Step (step 4) I follow this step until Add New operating system image. I cannot add here a install.wim? where is my problem? regards

Hi anyweb, yes I do these bits first until here: 1.bmp should I do these step too? 2.bmp should I do these step too? 3.bmp and go on my next question is why can I not see these step? 4.bmp thank you very much 1.bmp

Hi anyweb, I want to deploy Windows XP. By this Point: Create distribution point and then update it complete the following Step (step 4) do I have to continue all Step or only until to Continue to Part 2 >> or I have to go on to end of part 6? by step Add Operation System Install Package wizard must be a ISO data or do I have to do the contents? cheers

Hi anyweb, regarding my problem with sccm client, I think, why my sccm client does not working. It is DNS Server. The DNS Server is on Linux Suse installed and it is on the same LAN. I have Windows 2008 Server DC and the DNS Server is a Linux Suse. If I try on Windows Client to set the DNS IP Adresse from my Windows 2008 Server, then does function the sccm client immadiatley. But if I set on Windows Client the DNS IP Adresse from Linux Suse, then it does not function. How can I resolve it? Can you help me please? Regards P.S. See please on my issue (deploy Software, I cannot see in the ConfigMgr Client)

I am sure, AD is extended for my sccm

hi anyweb, thank yoo for your reply, I have checked sccm installation. I did run again the installation and choose "upgrade" and I let run the prerequisite checker and I see " All required prerequisite tests have complete" . No problem. it seems that AD Schema ist extended. let me know please why does it work fine on my Domain controller? I can depoly any software on DC without problems. cheers P.S. How can I set by deploying any software, where and on which local disk the software should be installed?

Hi anyweb, I am sure, that during installtion sccm 2007 sp1, I did Run the prerequisite checker and it did see " All required prerequisite tests have complete" . How can I checked whether AD Schema is realy extended? Can I extend AD Schema afterward? reagrds

hi anyweb, I set my SIDECODE=AUTOt, it happend nothing. Update: I have installed my sccm 2007 on a separate server Windows 2008 . My Domiancontroller is installed on a separate server Windows 2008 too. I can see this both groups SMS_SiteSystemToSiteServerConnection_sitecode and SMS_SiteToSiteConnection_sitecode on my sccm Side Server. But on my AD Domain I could not see these groups SMS_SiteSystemToSiteServerConnection_sitecode and SMS_SiteToSiteConnection_sitecode and I create these groups there. that means I have both groups as well on my Side Server as on my AD Domain. My Question is, do I need on AD Domain these groups SMS_SiteSystemToSiteServerConnection_sitecode and SMS_SiteToSiteConnection_sitecode???? or not? Is it the possible, that my problem with sccm client Configmgr does not function because of these groups on AD Domain??? cheers

here my SMSSIDECODE I think so,software distribution component installed correctly! here my advertisment tell me please, why does it work with my domain controller? do I have to set for every clients a boundary? thank for helping

I have on client many log files, which file do you mean? CAS.log in the CAS-log "Software Distribution Site Settings for the client are missing from WMI"

yes I follow all prerequisites before installing sccm 2007. The Ad schema is extened. I have a container named System Management. And Firewall is per policy disabled. MP role is there. the boundaries see please my scrennshot above. my boundary my MP my AD ( system Management) my Firewall why can I see on the domaincontroller all features of Configmgr? But on the Clients I see only this?